A toilet that keeps running after flushing is almost always losing water past a worn flapper, a stuck fill valve, or a float that is set too high - three parts that cost under $25 combined and take about 30 minutes to replace. In McLean, Virginia, where most of the housing stock dates from the 1960s through the 1990s, we see the same three failures over and over, and they are the reason a single toilet can quietly add $40 to $90 to a monthly water bill. The rest of this post walks through how to identify which part is failing, what the repair costs in 2026, and when it makes more sense to call us than to keep fiddling with the tank.
The short answer: your flapper, float, or fill valve is failing
Toilet keeps running after flushing McLean VA is a plumbing symptom, not a plumbing mystery. Water is escaping the tank when it should be sealed, so the fill valve keeps topping the tank back up, and the cycle never ends. You hear it as a hiss, a trickle, or a periodic refill every 20 to 40 minutes even when nobody has used the bathroom.
Three parts cause 95% of these calls:
- Flapper - the rubber seal at the bottom of the tank. It warps, hardens, or grows a mineral crust and no longer seats.
- Fill valve - the vertical assembly that refills the tank. The diaphragm inside wears out and stops shutting off cleanly.
- Float - the arm or cup that tells the fill valve when to stop. If it is set too high, water spills into the overflow tube continuously.
If you have hard water - and most of McLean does, with supply coming through the Fairfax Water system - the flapper is the usual suspect. Minerals chew through rubber seals faster here than in softer-water regions.
How a toilet is supposed to stop running
A working toilet completes its flush cycle in about 45 to 60 seconds. Here is the sequence, so you know exactly where yours is breaking down.
- You press the handle. The flapper lifts and dumps 1.28 to 1.6 gallons from the tank into the bowl.
- The flapper drops back onto the flush valve seat and seals.
- The fill valve opens and refills the tank to the water line - usually marked inside the tank wall.
- The float rises with the water and shuts the fill valve off once the tank hits that line.
- A small tube sends a trickle into the bowl to refill the trap, then everything goes quiet.
If any one of those five steps fails, the tank never reaches its shutoff point, and you get the sound you are hearing now. The fix is almost always in steps 2, 3, or 4.
The four reasons a toilet keeps running after flushing in McLean VA
1. The flapper is worn, warped, or mineral-crusted
This is the number-one cause we find on toilet repair McLean VA calls. A flapper has a working life of about 3 to 5 years. After that, the rubber loses its flexibility, and you get a slow leak from the tank into the bowl. You will not see water on the floor - the leak is internal, which is why it goes unnoticed for months.
Test it in 30 seconds: shut off the water supply, flush to empty the tank, then drop two or three drops of food coloring into the tank water that remains. Wait 15 minutes. If color shows up in the bowl, the flapper is leaking.
2. The fill valve is not shutting off
A fill valve that keeps running after the tank is full has a failed internal diaphragm. You will hear a constant hiss even when the tank is at the correct level. On toilets older than 10 years, we usually replace the fill valve rather than try to clean it - the plastic housing gets brittle and the cost difference is small.
3. The float is set too high or has lost buoyancy
If the float sits above the overflow tube, water spills down the tube and into the bowl forever. On older McLean homes with original 1980s toilets, we also see cracked plastic floats that fill with water and sink, which keeps the fill valve open. Adjusting the float takes two minutes with a screwdriver or a clip, depending on the model.
4. The flush valve seat or overflow tube is damaged
Less common, but real. A cracked flush valve seat or a hairline crack in the overflow tube will leak no matter how new the flapper is. This is where a running toilet stops being a $20 parts job and starts being a toilet replacement conversation.
How much water is a running toilet wasting in your McLean home?
A slow flapper leak wastes roughly 200 gallons a day. A fully stuck fill valve can push that past 500 gallons a day. At Fairfax Water's 2026 residential rate of about $5.50 per 1,000 gallons (water plus sewer), that is $33 to $82 a month, every month, until you fix it.
We have pulled bills for homeowners in Plumbers McLean VA in Chesterbrook where a single running toilet added $110 to a quarterly statement before anyone noticed. The toilet was 14 years old and the flapper had been leaking for at least eight months.
If your bill jumped and you cannot find the source, a running toilet is the first thing to rule out - before you start looking at irrigation leaks or slab leaks.
How to diagnose a running toilet in 10 minutes
You do not need special tools. A screwdriver, a flashlight, and a few drops of food coloring will get you to a diagnosis.
- Listen. Constant hiss means the fill valve. Periodic refill every 20-40 minutes means the flapper.
- Look at the water line. If tank water is above the overflow tube, the float is set too high.
- Food coloring test. As described above - this confirms a leaking flapper.
- Lift the flapper. Run your finger along the rubber edge. Crusty, stiff, or warped means replace it.
- Check the chain. A chain that is too short holds the flapper open. Too long and it gets caught under the flapper. Both cause a running toilet.
That five-step check tells you which part to buy before you drive to the hardware store.
Can you fix a running toilet without a plumber in McLean VA?
Yes, if the problem is a flapper, float, or chain. Those are genuine DIY repairs, and we tell homeowners so. A replacement flapper costs $6 to $12, a float is $5 to $10, and both install in under 15 minutes with no special tools.
Where it stops being DIY:
- The tank-to-bowl bolts are corroded and snap when you touch them.
- The shutoff valve under the tank will not close, so you cannot isolate the water.
- The fill valve needs replacing and the supply line is seized.
- You have already replaced the flapper and the toilet still runs.
Any of those four situations, and you are looking at a job that goes sideways fast. That is when a call to us is cheaper than the damage from a snapped bolt or a flooded bathroom floor.
What a running toilet repair costs in McLean VA in 2026
Typical 2026 pricing in this area breaks down like this:
- Flapper replacement: $95 to $150, parts and labor.
- Fill valve replacement: $135 to $210.
- Full rebuild kit (flapper, fill valve, float, supply line): $185 to $275.
- Flush valve seat replacement: $250 to $400, because the tank has to come off.
- New toilet installed (if the existing one is cracked or 20+ years old): $450 to $900 depending on the model.
Most of the calls we run land in the $95 to $210 range. If a quote comes in well above that for a standard flapper or fill valve, ask what else is being replaced.
Common mistakes we see when homeowners DIY a running toilet
We get called to clean up these five mistakes more than any others.
- Buying a universal flapper that does not fit. Toilet models have specific flush valve sizes. A flapper that is too large or too small will leak from day one.
- Over-tightening the fill valve nut. Hand-tight plus a quarter turn is enough. More than that cracks the tank.
- Adjusting the float without checking the water line mark. The tank has a molded line for a reason. Set the water level to it, not to the top of the overflow tube.
- Ignoring the supply line. If you are already replacing the fill valve, replace the $8 supply line at the same time. It is the next thing to fail.
- Forcing a corroded shutoff valve. If it will not turn by hand, stop. Forcing it snaps the stem and you now have water spraying in the bathroom.
None of these are expensive to fix. All of them are expensive to ignore.
When to call a professional
Call us when the shutoff will not close, when a bolt snaps, when you have replaced the flapper and the toilet still runs, or when the toilet is more than 15 years old and you are weighing repair against replacement. We handle those calls daily across McLean, from Plumbers McLean VA in Downtown McLean to the larger homes up in Langley Forest and Ballantrae.
We also want to hear from you if the running toilet has pushed your water bill up and you want a second opinion on whether the toilet is really the source. Sometimes it is; sometimes it is a leak detection McLean VA issue hiding behind the toilet noise. We check both before we quote anything.
One visit, upfront pricing, and the toilet stops running the same day.
Frequently Asked Questions
Why does my toilet keep running after flushing in McLean VA?
In McLean, the cause is almost always a worn flapper letting tank water leak into the bowl, which forces the fill valve to keep refilling. Hard water accelerates flapper wear, so most toilets here need a new flapper every 3 to 5 years. A stuck float or failing fill valve causes the rest.
How do I fix a running toilet in McLean Virginia?
Shut off the supply, empty the tank, and run the food coloring test. If color reaches the bowl, replace the flapper - a $6 to $12 part, 15 minutes of work. If the tank hisses constantly at the correct water level, replace the fill valve instead. Both fixes take under 30 minutes.
How much does it cost to fix a running toilet in McLean VA?
In 2026, a flapper replacement runs $95 to $150 with labor. A fill valve replacement is $135 to $210. A full rebuild kit - flapper, fill valve, float, and supply line - lands between $185 and $275. Most calls we run fall in the $95 to $210 range.
Can a running toilet increase my water bill in McLean VA?
Yes, significantly. A slow flapper leak wastes about 200 gallons a day; a stuck fill valve can waste 500. At Fairfax Water's 2026 rates, that is $33 to $82 added to your monthly bill. We have seen quarterly bills jump by $110 from one leaking toilet.
Is a running toilet an emergency?
Not usually. A slow flapper leak can wait a few days. But if water is actively spraying, the tank is cracked, or the shutoff valve will not close, shut off the main and call us - that is a same-day emergency, not a weekend project.
Get help with Plumbers McLean VA in McLean
If your toilet keeps running after flushing and you would rather hand it to someone who does this every day, we can be at your door in McLean today. We carry flappers, fill valves, and full rebuild kits on every truck, so most running toilets are fixed on the first visit.
Call +1 (831) 293-1204 and we will get it quiet again.

